RULAND MANUFACTURING Motion Control Couplings

Feature high torsional stiffness and zero-backlash, coupled with a balanced design to improve accuracy of motion and reduced vibrations at high speeds. Ideal for applications in servo and stepper motors and available in inch-to-metric bore combinations in different sizes, styles and materials

Ruland Manufacturing Metric Series single-piece motion control couplings are installed on two shafts moving at the same speed & in the same direction, for preventing misalignment (up to 3 degrees). The balanced one-piece design has 2 sets of three beams in the centre for high torque capacity, lower windup and increased stiffness. Cap screws firmly fit over the shafts, without causing marring on the surface. These couplings are tested beyond DIN 912 12.9 standards for maximum torque capability. Choose from a wide range of motion control couplings, available in aluminium and stainless steel variants on Raptor Supplies.

Ruland Manufacturing MOCT Series coupling oldham clamps are ideal for connecting shafts with misalignment while transmitting torque. They maintain precise alignment between two shafts while allowing axial movement to prevent angular, parallel and axial misalignment, protecting sensitive components and reducing wear. These clamps are used in automation, machinery and motion control systems. They have aluminium construction for a high strength-to-weight ratio and structural rigidity. These clamps feature anodised aluminium finish for protection against corrosion and wear while providing a smooth and visually pleasing surface. They have a maximum operating speed of 4500 RPM to effectively handle dynamic loads and maintain the integrity of the coupled components. These clamps also exhibit remarkable heat resistance up to 225 degrees F.

Ruland Manufacturing MW Series four beam couplings feature two sets of two spiral cuts to offer high torque capacity & low windup. These spiral couplings have a balanced design for reduced vibration at high speed. They come with small bearings for low radial forces and efficient performance. These set screw style couplings feature a compact design that fits into confined spaces and allows easy retrofits in existing equipment. They are manufactured from 7075 aluminium for light weight & low inertia, and 303 stainless steel for increased torque capability.

Ruland Manufacturing MW Series four beam couplings are designed for encoders and tachometers that use delicate components. These devices come with small bearings on the components for low radial forces and efficient performance. They provide extra flexibility to yield reduced bearing loads. MW Series flexible couplings feature a compact design that fits into confined spaces and allows ]easy retrofits in existing equipment. They have a helical cut pattern for providing great torque capabilities and low wind-up. These couplings are made of a single piece of 7075 aluminium for light weight and low inertia or 303 stainless steel for enhancing torque.

Ruland Manufacturing coupling hubs are designed for connecting shafts for torque transmission applications. These are one of the components for the three-piece design comprising 2, anodised aluminium hubs & a centre disk. These couplings can accommodate high parallel misalignments and operate with low bearing loads, thereby protecting sensitive system components. They have lightweight aluminium construction and black oxide finish for preventing abrasive fluids & particles from damaging the coupling hubs. Choose from a wide range of these coupling hubs, available in 7/8, 3/4, 5/8, 1/2 & 1 inch bore diameters.

Ruland OCC26-12-SS Oldham coupling clamps are used to connect two shafts in industrial machinery, automation systems, robotics and motion control applications. They enable the power and motion between the shafts while accommodating misalignment and reducing vibration. They feature aluminium construction to resist corrosion on exposed surfaces and have anodised aluminium finish for increased aesthetic appearance. These clamps offer a maximum angular alignment of 0.5 degrees and have a maximum speed of 4500 RPM. These clamps can withstand temperatures up to 225 degrees F.

Ruland Manufacturing P Series 4 beam couplings are used for running robots, computers, metering devices and medical equipment. These couplings provide zero backlash and feature a balanced design for minimising vibrations in devices working at a maximum speed of 6000 rpm. They are made from aluminium / stainless steel for corrosion resistance and fix angular misalignment up to 3 degrees. These motion control couplings deliver torques ranging between 5.5 & 92 inch-lb and can withstand temperatures up to 350 degrees F. Variants are available in outside diameters ranging from 0.75 to 31.8 inches.

Ruland Manufacturing coupling hubs are designed for connecting shafts for rotary torque transmission applications. These are one of the components for the three-piece design comprising 2, anodised aluminium hubs & a centre disk. These couplings operate with low bearing loads, thereby protecting sensitive system components like bearings and can accommodate high parallel misalignments. They have lightweight, 2024-T351 aluminium construction and black oxide finish for preventing abrasive fluids & particles from damaging the coupling hubs. Choose from a broad range of these coupling hubs, available in 5/16, 3/8, 5/8, 3/4 & 1/2 inch bore diameters.

Ruland Manufacturing OCT Series coupling oldham clamps are three-piece flexible shaft couplings employed to connect shafts in mechanical power transmission assemblies. They comprise two anodised aluminium hubs which press fit onto a centre disk. These couplings can operate under low bearing loads when securing sensitive system components and feature a balanced design for reduced vibration. They are available in 0.750, 1.000, 1.313, 1.625 and 2.250 inch clearance diameters.

Set screw style six beam couplings from Ruland Manufacturing are RoHS 3 & REACH compliant for light-duty power transmission applications. These units have a balanced design for reduced vibration at high speeds and two sets of three spiral cuts for high torque capacity & low windup. They test beyond DIN 912 12.9 standards and consist of multiple beam cuts to improve parallel misalignment capabilities. These couplings are made of 7075 aluminium for light weight & low inertia, and 303 stainless steel for increased torque capability.

Ruland Manufacturing coupling hubs are suitable for operating with low bearing loads to protect sensitive system components including bearings for motion transfer applications. These RoHS Compliant couplings feature balanced design for reducing vibrations at high speeds and lightweight aluminium construction for minimising backlash during the operation. They have black oxide finish for preventing abrasive fluids & particles from damaging the coupling hubs. Choose from a wide range of these couplings, available in 7 - 25 mm bore diameters.

Ruland Manufacturing coupling hubs are designed for accommodating high parallel misalignments in motion transfer applications. These REACH Compliant coupling hubs operate with low bearing loads for protecting sensitive system components like bearings and feature balanced design for reducing vibrations at high speeds. They have lightweight aluminium construction and black oxide finish for preventing abrasive fluids & particles from damaging the coupling hubs. Choose from a broad range of these coupling hubs, available in 8 - 20 mm bore diameters.

Ruland Manufacturing MOST Series set screw Oldham coupling hubs are ideal for establishing a connection between two parallel shafts that are closely spaced to transmit torque for use in mechanical power transmission assemblies. They feature aluminium construction for structural rigidity and corrosion resistance. These hubs can operate at a maximum speed of 4500 RPM and temperature of 225 degrees F. These screw sets allow a maximum angular misalignment of 0.5 degrees to reduce the chances of error and ensure reliability.

Ruland Manufacturing coupling hubs are ideal for connecting shafts for torque transmission applications. These are one of the components for three-piece design, comprising 2, SS hubs & a centre disk. These couplings operate with low bearing loads, thereby protecting sensitive system components and can accommodate high parallel misalignments. They have lightweight aluminium construction and black oxide finish for preventing abrasive fluids & particles from damaging the coupling hubs. Choose from a wide range of these coupling hubs, available in 7 - 20 mm bore diameters.